Baulinks – & gt; editorial || & Lt; older younger 2016/0899 & gt; & Gt; & gt; |
(06.29.2016) Surface water is made by means of drainage channels
different reasons collected – primarily to dewater
Areas but also …
- for protection of structures,
- the protection of groundwater,
- to maximize safety on roads, paths and squares
and / or - as a natural delivery to the soil by infiltration from
technical or soil-specific reasons it is not possible.
The effluent contains traffic areas surface water strong
Impurities and by tire wear, brake dust and oil
Gasoline traces are caused. Deposits of exhaust gases and to
carry building surfaces and diffuse heavy metal inputs by Components
today also to load in the groundwater. serve in this sense
various laws, regulations and recommendations to protect the environment – including …
- Water Act (CWA), as transnational
Framework law, - the country’s water laws of the federal states,
- the DWA-M 153 and
DIN EN 1433. ‘/ Li>
“standard tight from the outset” were
Probate means for receiving and removing surface water and drainage channels. Produced
annually in polymer concrete, concrete, plastic or metal more than 1
Million meters in Germany dropped from reputable manufacturers. The installation
is easy, because due to the modular design (standard length of 1 m)
they can be strung together to form a strand. If such a
Dewatering strand with a length of e.g. 50 m laid arise
but equally
many channel collisions. If these interfaces are not sealed, is the
collected water Although targeted but not without losses
Further processing or -Use derived. an over the gutter shocks
reach of the water in the soil. Against this background, the
ACO Tiefbau Vertrieb GmbH the gutter ACO Drain Multi LineSeal-in
presented. (For the record: The engliche “seal” means something like Siegel,
Sealing or technical seal.)
the development of the Seal-in technology had the objective of contaminated
to collect surface water and if possible without loss of treatment or
(Re-) transmit using.
- What is dense?
- How is tightness defined?
- How can channel collisions sealed permanently and economically
be?
After
DIN EN 1433 must gem at a tightness test. Section 9.3.6.
in constructively provided wetted cross section watertightness for
30 minutes ± 30 sec be detected.. With conventional gutters without
integrated seal this is only an additional operation after
laying the gutter elements on the construction site possible. If this happens
not, the tightness is not usually given. So it comes through leaky
Rinne shocks to pollutants in soil and groundwater. In a
Long-term test at
IKT – Institute for Underground Infrastructure in Gelsenkirchen
demonstrated by contrast, that of the ACO
Drain Multi Line with Seal-in technology are no leaks – so in
Installed state no water is discharged to the ground.
ACOs Seal-in technology is defined essentially by the
Formation of the gutter body made of polymer concrete to the end faces as well as the
used and factory installed EPDM sealing profiles. In addition to
through the use of the associated Seal-in-silicone grease as a lubricant
the juxtaposition setting the channel body can be facilitated.
The future with Seal in technology
With the development of ACO Drain Multi Line with Seal-in technology ACO has the
realized the first step of a phased program, the
the total range of ACO drain Drainage channels gradually both nationally and internationally
should follow. With the presentation of the first Seal-in-drainage channel on the
IFAT (from 30.5.
to 03.06.2016 in Munich) and the
GaLaBau (14th
to 17.09.2016 in Nuremberg) wants ACO the starting signal for the Mission
enter “standard tight from the beginning”.
for more information about
ACO Drain Multi LineSeal-in can be made by
email to ACO are required
See also for additional information. <- - Ce!>:
No comments:
Post a Comment